Domestic ACS Gas Training Courses – Reassessment Only

CCN1 (inc CPA1) and up to 3 appliances (normally CENWAT/CKR1/HTR1)
Duration: up to 2 days (no training however, covered below to demonstrate the depth of changes that can occur between your refresher assessments)
Cost: £495+VAT

CCN1, Domestic Gas Safety, is the core qualification and is normally a pre-requisite to have before attaining other additional qualifications. There are some exceptions to this, but generally most candidates must complete CCN1, or already be in possession of this qualification before adding others. In broad terms CCN1 contains the following core modules.

• Gas Safety Regulations
• Emergency Actions
• Combustion
• Ventilation
• Flueing
• Gas pipework
• Let-by & tightness testing
• Re-establishing gas supplies
• Pressure regulators
• Gas rates & pressures
• Gas controls
• Emergency valves
• Unsafe situations

As you can see CCN1 (inc CPA1) contains several modules and therefore refresher training takes a number of days to update you on. You must also allow time to undertake and successfully pass the associated theory and practical assessments associated with CCN1. These can also take a day or more to complete, again dependant upon the time you as an individual might need.

CENWAT1, Domestic Gas Fired central heating, water & heaters, covers what you need to know in order to safely install, service and repair this particular category of appliances. Broadly, the course covers updates within the following areas.

• Checking the Heating requirements & appliance outputs
• Checking the intended installation site.
• The gas connection and supply pipes
• Securing the appliance correctly
• Ventilation requirements
• Flueing requirements, including condensate outflow
• Tightness testing
• Operating pressures
• Flushing, commissioning and testing the appliance / system
• Other ‘site specific’ checks and tests

CENWAT1 refresher training is normally completed within a day, plus additional time to sit the theory & practical assessments.

CKR1, Domestic Gas Cooking Appliances, covers what you’ll need to know in order to safely install, service and repair domestic gas cooking appliances. Broadly, the course covers updates within the following knowledge areas.

• Checking the intended installation site.
• The gas connection and supply pipes
• Securing the appliance correctly
• Ventilation requirements
• Tightness testing
• Operating pressures
• Commissioning and testing the appliance
• Other ‘site specific’ checks and tests

CKR1 refresher training is normally completed within half a day, plus additional time to sit the theory & practical assessments.

HTR1, Domestic Gas Fires & Wall Heaters, covers what you’ll need to know in order to safely install, service and repair domestic gas fires & wall heaters. Broadly, the course covers updates in the following knowledge areas.

• Checking the intending installation site.
• The gas connection and supply pipes
• Securing the appliance correctly
• Ventilation requirements
• Flueing requirements
• Tightness testing
• Operating pressures
• Commissioning and testing the appliance
• Other ‘site specific’ checks and tests

HTR1 refresher training is normally completed within half a day, plus additional time to sit the theory & practical assessments.

CPA1, Flue Gas Analysers, covers what you’ll need to know in order to use a flue gas analyser throughout your training and linked to Core Gas Safety and individual appliances.  Broadly, the course covers updates in the following knowledge areas.

• Overview of flue gas analysis
• The detection and measurement of gaseous particles in the air / flue-ways
• The dangers of carbon monoxide and it’s affect on health / life
• Measuring % oxygen levels present
• The use of analysers to check correct combustion and gas rates
• Testing operational efficiency of appliances
• Assisting to determine whether appliances require further maintenance
• Safe actions to undertake, based upon measurements detected
• Other ‘site specific’ checks and tests

CPA1 refresher training and assessment is now incorporated within all relevant modules. Please also note that since April 2012 CPA1, Flue gas analysers, are also a mandatory requirement. If you are retaking your CCN1 or taking it for the first time it will be included within the CCN1 core assessment.